peel-a-way ? dip socket terminal carriers dip sockets 5 energy w ay , w est w arwick, ri 02893 usa t el: 800.424.9850 | 401.823.5200 fax: 401.823.8723info@advanced.com | www .advanced.com cat alog 16a products shown covered by patents issued and/or pending. specifications subject to change without notice. inch/(mm) specifications: terminals: brass - copper alloy(c36000) astm-b-16 contacts: ber yllium copper - copper alloy (c17200) astm-b-194 solder preform: standard: 63sn/37pblead-free: 95.5sn/4.0ag/0.5cu plating: g - gold over nickelm - matte t in over nickel t - t in/lead over nickel gold per astm-b-488matte t in per astm545-97 t in/lead per mil-p-81728 nickel per qq-n-290 features: ? peel away terminal carrier aftersoldering. ? disposable carrier . ? complete soldering visibility onboth sides of pcb. ? maximum air flow . ? better flux rinse. ? no contact damage due toterminal carrier insertion. ? no contact pull out due toextraction of terminal carrier . solder preform terminals .072 dia. (1.83) .020 dia. (.51) .110 (2.79) .130 (3.30) solder preform .072 dia. (1.83) .165 (4.19) .125 (3.18) .020 dia. (.51) solder preform tin/lead: type -150 lead-free: type -811 tin/lead: type -151 lead-free: type -812 ks 3 16 - 85 m g body type terminal typesee options on next page dip spacing3 - .300/(7.62mm) 4 - .400/(10.16mm) 6 - .600/(15.24mm) 9 - .900/(22.86mm) number of pins(8 to 64) additional sizes available - consult factory. contact plating terminal plating rohs compliant: g - goldm - matte tin t - tin/lead rohs compliant: g - goldt - tin/lead rohs compliant insulators: ks - peel-a-way options tape seal - add 3m to end of part number ? removable t ape seal protect s plated cont act in harsh environment s ? sealed socket will not allow dirt and other cont aminant s to enter socket chamber and become entrapped behind cont act fingers ? s pray flux without cont aminating cont act area table of models description: peel-a-w ay ? socket (ks) material: polyimide filmindex: -269c to 400c (-452f to 752f) polyimide film .005(.13) note: t erminals plated with matte t in are available only with gold plated cont act s. how to order material silicone backed polyimide film, -74c to 260c (-100f to 500f) intermittent to 371c (700f) tin/lead: type -111 lead-free: type -810 .058 dia. (1.47) .038 dia. (.97) .155 (3.94) .031 (.79) solder preform peel-a-w ay ? only for molded insulators, see p ages 28-29. (shown here on molded socket) see pg. 29 for intrusive reflow application.
how to use: 1. place socket on pc board. 2. send pc board and socket throughsoldering operation. 3. peel away polyimide film carrierfor complete solder joint visibility or leave in place for added stability . polyimide film peel awayafter soldering to pcb. pcb solder fillets visible both sidesfor inspection and cleaning. dip sockets peel-a-way ? dip socket terminal carriers 5 energy w ay , w est w arwick, ri 02893 usa t el: 800.424.9850 | 401.823.5200 fax: 401.823.8723info@advanced.com | www .advanced.com cat alog 16a products shown covered by patents issued and/or pending. specifications subject to change without notice. inch/(mm) 8 .300 (7.62) .400 (10.16) .400 (10.16) 10 .300 (7.62) .400 (10.16) .500 (12.70) 12 .300 (7.62) .400 (10.16) .600 (15.24) 14 .300 (7.62) .400 (10.16) .700 (17.78) 16 .300 (7.62) .400 (10.16) .800 (20.32) 18 .300 (7.62) .400 (10.16) .900 (22.86) 20 .300 (7.62) .400 (10.16) 1.000 (25.40) 22 .300 (7.62) .400 (10.16) 1.100 (27.94) .120 (3.05) .110 (2.79) .028 dia. (.71) standard terminals type -33 type -51 type -04 type -49 low profile solder t ail .165 (4.19) .125 (3.18) .020 dia. (.51) .130 (3.30) .110 (2.79) .020 dia. (.51) .095 (2.41) .095 (2.41) .028 dia. (.71) super low profile ultra low profile low profile solder t ail type -85 type -176 .038 dia. (.97) .030 (.76) .125 (3.18) .034 dia. (.86) .030 (.76) .125 (3.18) type -210 .034 dia. (.86) .015 (.38) .140 (3.55) b c a .005 (.13) # of pins a b c near flush solder t ail near flush solder t ail near flush solder t ail 24 .300 (7.62) .400 (10.16) 1.200 (30.48) 28 .300 (7.62) .400 (10.16) 1.400 (35.56) 40 .300 (7.62) .400 (10.16) 2.000 (50.80) 16 .400 (10.16) .500 (12.70) .800 (20.32) 20 .400 (10.16) .500 (12.70) 1.000 (25.40) 22 .400 (10.16) .500 (12.70) 1.100 (27.94) 24 .400 (10.16) .500 (12.70) 1.200 (30.48) 28 .400 (10.16) .500 (12.70) 1.400 (35.56) 32 .400 (10.16) .500 (12.70) 1.600 (40.64) 10 .600 (15.24) .700 (17.76) .500 (12.70) 18 .600 (15.24) .700 (17.76) .900 (22.86) 20 .600 (15.24) .700 (17.76) 1.000 (25.40) 22 .600 (15.24) .700 (17.76) 1.100 (27.94) 24 .600 (15.24) .700 (17.76) 1.200 (30.48) 28 .600 (15.24) .700 (17.76) 1.400 (35.56) 32 .600 (15.24) .700 (17.76) 1.600 (40.64) 36 .600 (15.24) .700 (17.76) 1.800 (45.72) 40 .600 (15.24) .700 (17.76) 2.000 (50.80) 42 .600 (15.24) .700 (17.76) 2.100 (53.34) 48 .600 (15.24) .700 (17.76) 2.400 (60.96) 64 .600 (15.24) .700 (17.76) 3.200 (81.28) 32 .900 (22.86) 1.000 (25.40) 1.600 (40.64) 36 .900 (22.86) 1.000 (25.40) 1.800 (45.72) 40 .900 (22.86) 1.000 (25.40) 2.000 (50.80) 52 .900 (22.86) 1.000 (25.40) 2.600 (66.04) 56 .900 (22.86) 1.000 (25.40) 2.800 (71.12) 64 .900 (22.86) 1.000 (25.40) 3.200 (81.28) surface mount options available # of pins a b c additional standard and custom terminals available.see t erminals section or consult factor y. note: t erminals shown with insulator removed. available online: ? rohs qualification t est report ? cad drawings dimensional information express deliveryt erminals shown with the new express symbol are available in most insulatorbody types with fast lead time. some quantity and plating restrictions apply . sear ch our distributor inventor y online at www .advanced.com, or check with customer ser vice for availability .
|
